Why Nobody Cares About Audi G28 > 자유게시판

본문 바로가기

사이트 내 전체검색

뒤로가기 자유게시판

Why Nobody Cares About Audi G28

페이지 정보

작성자 Verena 작성일 24-11-19 07:41 조회 3 댓글 0

본문

How to Replace an audi spare key replacement G28 Engine Speed Sensor

In this video, Charles the humble mechanic demonstrates how to replace the G28 engine speed sensor. The sensor is located at the edge of transmission, above the flywheel gear. It sends a message to the ECU via a grey wire T55/49, then to the tachometer in the instrument cluster.

1. Engine Speed Sensor

The grey wire is situated on the outside of the transmission, directly above the flywheel ring. The sensor sends an electrical signal through the grey wire to pin T55/49. The ECU utilizes this information to control fuel and boost. It also sends an alert to the G5 Tachometer within the instrument cluster.

The sensor is used as a reference to correlate with the G40 Camshaft Position Sensor. The ecu has to be aware of when the crankshaft has reached TDC and also the position of the camshaft, to trigger the spark and injectors.

If this sensor fails, the ECU will display a P00160 error code. This means that the Crank Shaft is not in sync with the Intake Camshaft. It could also be a sign of a chain stretch or a jumpy chain link in the upper chain. However, the error code won't be displayed on its own without additional information from other sensors (G4 and G40).

Testing is a bit tricky because there are two connector pins, and they perform different functions but the most effective method to test it is to measure the resistance between the sensor and the ECU. If the sensor is operational, it should read approximately 1000 ohms. Look for signs of coolant or oil in the connector bay if you are experiencing issues with this component.

2. Injectors

Yesterday accelerating full speed from highway paytoll, I experienced massive power loss as if the engine was running out of gas or the injectors aren't firing at all. I took out the spark plugs this morning, three were soaked with gasoline and the 4th was dry. When i crank the engine, there are no sparks, I put a piece of tissue on top of each injector hole and the 3 that were drenched in gazoline jump out but the 4th stays shut. I inspected the ground connection on ECU pins 14/55/30/55/48/55/14/55/48/ I get 0ohm. I'm assuming the issue is in another place.

I also tried to reset the PID but with no luck. The car can start when the G28 is not plugged in and runs fine when it is plugged in however it has the intermittent misfire issue at higher RPM. The coolant sensor (G62) even when it is unplugged, shows temperatures of -49c. I also noticed that the oil gauge in the cockpit shows 2 bars when the actual pressure is 0.

I'm not sure what to do. I think I've all other possibilities out. However, i'm afraid that i might have missed something. If anyone has any ideas please share them! TIA!

3. Fuel Pump

The fuel pump of the g28 receives a signal from the RPM sensor. The GM-style transmitter is the same as the G4 and both function in the 80, 100 200, UrS and RS2 cars which is why you can easily locate one at a junkyard or in a local parts store. It is easy to test them - just put your DMM into resistance mode and measure the distance between pins 1 and 2 (with the bump at the connector's end facing upwards). They must be infinite ohms.

4. ECU

Our 20vt turbo (3B AAN, ABY and ADU) engines are equipped with an ECU that needs to know the speed and position of the crankshaft in order to make a decision about timing of the fuel injectors, etc. It utilizes a Crank Position Sensor G4 and an Engine Speed Sensor G28 to accomplish this. If you have a problem with either one of these, the diagnostic scanner will display codes that could cause an engine shut down.

Some of the symptoms of a malfunctioning G28 sensor are an inaccurate gearbox rev counter, gears shifting quicker than normal and/or a misfire when you're in gear. If you experience any of these problems, it is most likely that your sensor is deteriorating and should be replaced. They are cheap and easy-to-find especially when they're an Bosch model like ours. Alternatively, the GM version of this component is also a good option.

5. Tachometer

A faulty engine speed sensor could be a cause for many issues in your vehicle. It's an essential component of the audi key fob replacement Tt Key case (brewwiki.win)'s transmission because it communicates to the ECU about how fast or slow the car's crankshaft is turning. This sensor could cause the transmission to fail and other components in the car to be affected.

The G5 engine sensor is located near the edge of the transmission, over the flywheel ring. It transmits a signal via gray wire to ECU pin T55/49. The ECU then processes this signal to control fuel, timig and boost and then sends it on to the G5 tachometer inside the instrument cluster. You can test for sensor failure by checking continuity from the sensor to the tachometer. You can also check continuity between pin T55/49 of the ECU and pin T6a/1 of the instrument cluster (trace [79trace [79]) and between pin T6a/1 and pin T26a/12. It should show approximately 1000 ohms of resistance between those points. This is a common part across the replacement audi key cost 80 100 200, UrS and RS2 range from 1985 MC through the 1997 UrS AAN and 1995 RS2 ADU, so the best ones might be availble in wrecking yards.SEAT-Logo-2019.jpg

댓글목록 0

등록된 댓글이 없습니다.

Copyright © 소유하신 도메인. All rights reserved.

사이트 정보

회사명 : 회사명 / 대표 : 대표자명
주소 : OO도 OO시 OO구 OO동 123-45
사업자 등록번호 : 123-45-67890
전화 : 02-123-4567 팩스 : 02-123-4568
통신판매업신고번호 : 제 OO구 - 123호
개인정보관리책임자 : 정보책임자명