Five Killer Quora Answers On Boarding Up A Door > 자유게시판

How to Go About boarding up a door (King-wifi.win)

boarding up service up a door is one way to protect vacant investment properties from the elements. Although it isn't able to stop all damage, it can reduce some of the issues caused by severe storms.

commercial boarding up service up windows and doors can also deter burglars, vandals, and squatters. However, it can be expensive and time-consuming to install plywood boards over the openings on a house.

Measure the Door

The first thing you'll need is an accurate tape measure. It is a good idea to keep a chair or ladder nearby in case you need an improved view of the top of the frame. Wear gloves and goggles in the event that you need to use these tools.

Once you have the measuring instrument, start by taking the door's width measurement. You can do this by running a tape measure horizontally along the door. Be sure to remove all extra parts of the door, such as the sweep, when measuring. Then, determine the height by measuring from the floor up to the sill or the lintel. It is essential to measure in multiple places particularly with older doors, because they are not always a perfect rectangle. If the measurements are different then use the largest number.

After you've logged the measurements of height and width and you'll need to determine the size of emergency boarding up 24/7 you need for the frame. Ideally, it should be 2 inches wider than the door and 1 inch thicker than the door. 2'' higher. This will give enough space to shim both the door and frame to fit.

It's a good idea to remove the casing or trim around the jambs of the door to see the studs. This will help you determine the exact size of the space between the studs and the edges of the frame.

After you have removed the trim, measure the width of your door frame using the tape measure. Measure the frame at three different places and use the smallest measurement. It is also important to determine the height of the frame from top to bottom on both sides. Choose the shortest measurement for the width of your door.

If you're having issues with these measurements, it's a good idea to consult an expert and have them come out to your house to do the measuring for you. They'll be able determine the exact kind of door and size you need and how to prepare the frame for the new door.

Cut the Plywood

A door frame is typically made up of a series thin boards or studs that create a hollow space around the door. A typical door is held in place by two hinges connected to the studs. If you are looking to refinish doors, you'll have to take it off its hinges over night. Placing plywood in the door opening is an easy method to board the door and keep insects from gaining entry into the home. It is simple to do this without having to nail or screw the plywood to the door's frame.

Plywood is affordable, simple to work with, and looks great when it is finished. This makes it the ideal material to provide a temporary solution to a problem that requires removing the door that is in use and renovating or installing a brand new one. It can be used to secure the opening of a room that is being renovated, such as the construction site or basement.

Begin by taking measurements of the width of the door opening as well as its height. Note the measurements on the plywood with an utility knife and a drywall square or other straight edge of metal. Then, draw an outline of chalk across each line to indicate where to cut. Use a circular blade to cut the plywood to the desired size.

It is crucial to shield your eyes and ears when cutting plywood. If possible, wear a pair of safety goggles and earplugs when working. Additionally, it is important to use a blade with a large number of teeth that cut quickly and without tear-out. Use a small piece of wood to guide the blade. Keep it a hair's breadth away from the marked line when cutting.

An effective way to hold the plywood in place without fixing it to the studs is by fixing two braces at each end. Place one of the braces on the side of the door, and the one on the outside. Then, insert two 1-1/2-inch deck screws into each of the holes and tighten them with an open-end wrench.

Fasten the Plywood

When you have a piece of plywood cut to the right size and with the holes for stiles and rails predrilled and ready to fasten the panel to the door frame. This is a straightforward project that doesn't require advanced carpentry skills if you use the correct tools and follow the right procedures.

Set up a table near the entrance with two sawhorses at each end, and framing lumber 2x4s. Utilize the marks you made during the measurement process to guide you while cutting the plywood. Use a utility blade and a straight edge made of metal to score the lines. This will provide a guideline for the saw blade and help prevent splintering when you cut the plywood.

Wear eye protection and cut along the lines of scoring using a circular or table saw with a fine-tooth blade. Sand the edges of the panels with 120-grit paper to smooth it out and remove any burrs. After the sanding, apply a layer of wood sealer on the plywood panels, and let dry as directed by the manufacturer.

Install the hinges on the door frame. If you're using a hinge with a T-hinge drill holes on the outside face of your door for the straps portion of the hinges. Then, place the outside hinge on its spot and attach it to the frame with a screw gun. Repeat the process on the inside of the door for all of the remaining hinges, being cautious not to tighten too much on one of them or the hinge could shift.

If you have only a single hinged outside door it is possible to make it easier to close by fishing an electrical wire through the loops of the outside hinges. Bend a small piece of tie wire in half, and place it through the two holes on the outside of the door. You can then twist the wires together to tighten them and fix the door.

Install the Plywood

Install the plywood in the door's opening by using the measurements you have taken. Move the header of the frame (top) and the sill. Use a level and ensure that there is no slop between the header and sill. If it isn't perfect then place another shim if necessary and continue the process until the sill and the header are level.

Once the plywood has been put set, secure it with the stainless-steel hinge bolts and wingscrews. Use a screwgun with an attachment for a hex head to prevent removing the heads of the screws.

If your house has studs running along your doorway, you could drill hanger bolts into each of the framing members. This is a lot easier than using a drywall cutter to create the hole.

After you have installed the plywood after installation, take measurements of the width and the height of the door opening. If necessary, cut your bottom of the plywood to match the height the door frame. Cut two pieces of framing wood 1-by-6 to serve as braces for the lower and upper ends. Cut along the lines drawn on your plywood using circular blades with teeth that are finely-toothed. Wear eye protection. Splinters can be removed from the cuts by using a sanding tool.

After you've put in the braces, use two pairs of 2-inch finishing nail to attach each brace to the plywood. When you're finished counter-sink the heads of all nails. Seal the braces and the plywood with a quality wood sealer such as this wipe-on polyurethane from Minwax.

If the door is still too large for your doorway, you could add an ornamental molding to fill in the space between the door and jamb or you can reduce the size of the opening. In most cases, however it is less expensive and easier to simply buy an entirely new door. It also eliminates any issues you might have encountered with your original door even if it was damaged or no longer fitted the opening.