Guide To Fix Door Hinge: The Intermediate Guide In Fix Door Hinge > 자유게시판

How to fix Door hinge a Loose Door Hinge

The majority of homeowners can fix hinges that are loose. However, if the holes for screws are smashed and can't hold screws, you might need to put in wood glue and dowels before you can install the hinge.

Before you do this, however scrub away any surface rust. This will aid in keeping the dowels in place and provide a solid base for them to rest on.

Take the Hinges off

Many standard door hinges can be removed, making it simpler to move the door from one end of the frame to the other side or take the entire door off when needed. Removing the hinges is fairly simple for anyone with a bit of patience, but you have to know how to do it right.

If the hinges have been painted it is necessary to remove it prior to trying to remove the pins. If you don't, the paint will flake off and scratch the door when you attempt to lift it. To break the seal of the paint put the hinges into a stainless steel dish and fill the pan with water until the hinges are completely submerged. Let the hinges sit in the pan for 30 minutes. The heat from the water will soften the paint making it easier to take off.

Once the pins have been removed, take the hinges and the frame from the door. You can make use of a screwdriver to get the job done, but it is recommended that you make use of a magnetic screwdriver for this task. This type of screwdriver has been specifically designed to grab metal screws and help you get the job accomplished much faster.

It is a good practice to spray lubricant on the hinges before attempting to remove them. A simple lubricant can make the process move along quickly and aid in the removal of the screws and pins. This type of lubricant can be found at most hardware stores as well as home improvement shops.

The number of hinges you need will also differ based on the kind of door you have and how it's installed. Solid-cored and heavier doors will require more hinges, whereas hollow-cored doors that are lighter may only require two or three hinges.

It is also important to understand the different types of hinges so you can determine which ones work best in your situation. Exterior hinges are typically designed to support the door's weight however, interior hinges will have to be able to support lighter loads.

Reattaching the Hinges

Sometimes, the hinges on doors loosen over time and start to hang out of alignment or slide. This can be a problem but is usually easy to solve. Most of the time, a simple retightening of the screw will resolve the problem. However when the screw holes are ripped out, this can be more difficult. A wood dowel can be used to tighten these holes once more.

Begin by drilling out the hole you had previously made using an appropriate drill bit similar to the size of the new screw (typically 3/8"). Fill in the hole with wood glue and a wooden stick. The dowel should be cut to a length the same as the screw to ensure a snug fit. Then, you can reinstall the screw and tighten it until the desired degree of tightness. If the upvc door hinges continues to bind up, add another dowel to the gap. Repeat the process. Close the door slowly after each adjustment to make sure that the clearances around the perimeter are correct.

Another option is to just use an old-fashioned wood plug instead of dowel. It will work just as well but might take a little longer to put in. Simply whittle a plug of wood to the proper size to ensure a secure fit, then tap it into the hole. If you don't own an instrument for woodworking or toothpicks, you can make use of toothpicks or matchsticks made from wood.

Make use of a countersink to make the hole smaller for the head of the screw after you have installed it. This will prevent the screw from rubbing against the edges of the bifold doors hinges when they are closed and opened. This will make it easier to tighten the screw when you are reinstalling the hinge.

After reinstalling the hinge, lubricate the hinge with dry lubricant. This will help prevent it from getting stuck in the future. You can use products like PB Blaster and Liquid Wrench. Apply a thin coating and allow it to penetrate the hinge barrel for about 15 minutes.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door, you are able to make a few repairs. Verify that the screws that hold the hinge plate to both the door frame and the frame are tight. If they're loose, tighten them with an electric drill or screwdriver. Be careful not to tighten the screws so tight that they cause gaps at the trim joints, or worse cause threads to be stripped.

If the issue is that the hinge plates are breaking and you want to reattach the plates by applying wood glue on the back of them and then inserting toothpicks or wooden dowels into the holes. The dowels or toothpicks serve as a solid base for the screws and help prevent the plates from shifting when you drive them into position. Allow the glue time to dry before you can reattach your hinge.

Another common cause of loose hinges is that the screws are stripped or gone. You can fix this problem by replacing the screws with longer ones. Make sure you use a drill bit that is compatible with the size of the screw hole in order to avoid drilling into other parts of the hinge or jamb.

Close the door once you have reattached your hinge and examine the gap between the frame and the door. It should be approximately the thickness of one nickel all around, or less if there's a gap created by a door that hung improperly. If the hinges were installed correctly, this shouldn't be a problem.

If you discover that the hinges remain loose, you can try adding an extra thicker shim between the hinge plate and the mounting surface, to create an extra inch of space. You could also try removing the hinge pin from the problematic hinge and pounding it down with a hammer to make it tighter or use an entirely new hinge pin. It is also possible to lubricate the hinges with mineral or Jojoba oil to lessen friction and help them hold their position. Regularly lubricating your hinges will aid in keeping them from becoming stiff or squeaky and can also extend their life.

Cleaning the Hinges

A hinge's continuous movement creates friction, which attracts dust particles. These particles can get stuck and accumulate over time in the moving parts of door hinges, if they're not regularly cleaned and lubricated. The hinge will become stiff and creaky, and its appearance could rapidly diminish. Regular cleaning, lubrication, and inspection can preserve the quality of a door's hinges and ensure their proper function.

Examine the hinges for the accumulation of rust. If the rust has become so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace them. If you are able to save the hinges, begin by brushing away loose rust using steel wool and a wire brush. Apply a commercial rust removal solution or homemade solutions like lemon juice to the hinge. Allow the rust-removing solution to remain on the hinges for several minutes to penetrate and dissolve the remaining rust.

The tightening of screws can restore hinge function if you don't want to spend money or time on replacing hinges. It is possible, however, to add a wooden shim or dowel to the hinge if the screw holes have been degraded. Dowels made of wood are round pieces of wood in the form of rods which are available in various lengths and sizes. They are available at home improvement centers or woodworking supply shops, or online.

A shim can be made of plastic or metal, depending on the type of hinge you've got. To make a dowel, cut an unfinished dowel into the desired length. You can then dip a dowel into carpenter's adhesive and insert it in the hole. The glue will secure the dowel in the desired position.

Before cleaning the hinges, lay down a paper cloth or towel to protect your flooring from spills. After the area has been secured and dry, clean the hinges with a soft cloth or sponge coated with a mild cleaner or vinegar to remove dirt, grime, and tarnish. You can make use of a small or toothbrush brush to reach difficult-to-reach places in crevices or tight areas.