12 Companies Are Leading The Way In Door Lock Change > 자유게시판

How to Do a Door Lock Change

Door lock replacement is a quick and cheap method to boost your home's security. This process isn't for all. It requires a certain amount of patience window and door lock repair skill.

The cylinder is inside the knob body. The cylinder is responsible for recognizing the key as it is put into the lock.

Take off the lock that was previously used.

The first step in replacing a door lock is to get rid of the old one. It is a fairly simple process, but you must keep some things in mind. First, make sure that your new lock is the right size for the door you have. This will ensure that it fits snugly and doesn't create a gap around the deadbolt plug or latch.

Once you have removed the latch plate, look for two screws or bolts on the inside of the casing that hold the casing and the halves of the lock together. Unscrew these with a screwdriver, then remove the lock from the door. If you have a mortise locking mechanism there is a set screw that binds the handle to the spindle. Remove the doorknobs by unscrewing the screw using the help of a screwdriver.

Remove the deadbolt as well as the latch plug from the door jamb. Install your new lock. If you are replacing a mortise lock you should also measure the distance between the lock case and the door's edge to ensure that your new lock will be able to fit.

There are a variety of reasons that could prompt you to change your door lock, including suspecting that someone else has the key, or you are welcoming a new roommate. In any event, you can save money by taking the lock off yourself instead of paying a professional to do it. It's much simpler than most people imagine and can be completed in a matter of minutes.

Remove the trim and handle from your door. Then, you can pry the trim off using a screwdriver that is flat. It should be possible to pull off the majority of it. In some cases, you may even be able to take off the handles completely. Next, search for a pinhole on the inside of the handle and insert straightened clips into it. This will activate the release mechanism and allow you to take the handle from the door. Then, look for a small tab in the interior of the window lock replacement near me, and press it using a flat screwdriver. Once the spindle has been removed, you can then remove the housing and cylinder.

Selecting a new lock

There are a lot of options available when it comes to selecting the right lock. Take a look at the various types of locks and choose one that fits the style of your door. Think about the backset which is the distance between the edge window and door lock repair the middle of the hole for the lock. Also consider the cross bore, a small hole in the middle of your door frame. Select a lock that will fit the door thickness and swing.

The American National Standards Institute and BHMA have graded most door locks to give an idea of their strength and the difficulty to pick them up or disable them. A grade 3 lock might be ideal for a quiet suburban apartment complex, whereas the grade 1 lock may be more able to withstand the traffic near a busy store front on a city street.

Most smart door window locks Repair require a digital key code to open. If you're concerned about hacking or other security issues you should consult a professional locksmith or your local police department for advice.

Replacing the cylinder

If the cylinder of your door lock is broken or damaged it can be replaced within a matter of minutes using a simple DIY project. It is crucial to choose the correct cylinder and follow all instructions. First, take off the handle or knob if it is present. Then, using a screwdriver, remove the trim that is around the lock cylinder. After the trim is removed, you can access the screws that secure the cylinder and remove them using a flathead screwdriver. The cylinder is then gently pulled away from the door.

Make sure you measure the length of the new cylinder before installing it. With a tape measure, measure the distance between the center of the cylinder and the left and right sides. Purchase a new cylinder that has the same measurements. This will stop the cylinder from snapping, which could happen when the door is kicked out or when the key sticks inside.

Insert the replacement window lock cylinder in the door and then turn the key. This will align the cylinder with your carrier that is usually located on the outside of the lock. Then, loosen the set screws that should be only a couple of turns into the head. It is also necessary to loosen the screw in the edge of the door that fastens the case, if there is one.

After taking the lock cylinder out and replacing it with a new lock by slipping the new cylinder into the case and tightening the set screw. Installing the part that connects the cylinder to a lock indicator stem is also essential. This can be done by pulling three tabs in the back of the cylindrical with needle-nosed pliers. Then, you can connect the smaller bracket to the back of the cylinder. You must then install the strike plate and latch plate, as well as the retaining rings fixed to the top of the lock cylinder.

Installing a new lock

Start by measuring the door's width if you are replacing a lock that is already in use. Most locksets for residential use are designed for doors with a thickness of 1 3/8 - 3/4 inch. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll require a stronger door kit. This will include longer screws as well as a longer spindle extension or tail piece for door knobs.

The majority of locks come with a thorough installation guide to assist you. Before you begin, read the instructions to ensure you have followed all the steps. The manual will give you a clear idea of the level of skill that is required to complete the task. You may want to seek out a friend who has had experience in changing locks for help if you are changing double glazing window locks replace for the first time.

It's a good idea to tape the openings in the old hardware prior to installing the new lock. This will stop the screws from falling through the holes and will also protect any tiles you may have installed. It will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch includes the masking strip or gaffer tape. However, you can make use of any tape you have.

After you have removed the screws that hold the inside of the lock section to the exterior side, pull it straight away. It's important to do this quickly so that the lock doesn't end up accidentally closing on itself and damaging the mechanism.

Fit the new latch bolt in the upper cross bore of your new lock if it has one. Make sure that you place it in the proper location, which is marked by an arrow. Then, screw the latch plate onto the bolt.

Finally, screw the deadbolt and strike plate into the door jamb. Test the deadbolt by throwing it few times to verify that it extends all way into the strike plate and is completely secure. If you're using an electronic smart lock, make sure to follow the instructions to program it. This involves downloading an application, registering your email address, confirming your identity, and accessing the wireless network to add your device.